CoDrone Pro remote not connecting

[athang]

Hi,

I tried uploading code to the CoDrone Pro remote, and I receive an error message with feedback that says "the selected serial port does not exist or your board is not connected".

I checked the following items with a few run-through to make sure that the steps of connection are correct and I was not missing anything.

• Switch 1 is Up, Switch 2 & 3 are Down
• Pressed the "Reset" button under the switches and bluetooth button before upload. I see solid red light under Power, blinking blue light on Led 18, and blinking yellow light above Bluetooth button (sometimes can be blinking red).
• Selected the correct board (Rokit-SmartInventor-mega32_v2) and the port
• Used different USB ports and computer systems (Windows & Mac)

I still run into the same issue. I have copied the detailed error message. Sorry about the long post.

Arduino: 1.8.5 (Windows 10), Board: "Rokit-SmartInventor-mega32_v2"

C:\Program Files (x86)[hidden path details]

Detecting libraries used... [more hidden path details]
Generating function prototypes... [more hidden path details]
Compiling sketch... [more hidden path details]
Compiling libraries...
Compiling library "CoDrone"
Using previously compiled file: C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229\libraries\CoDrone\CoDrone.cpp.o
Using previously compiled file: C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229\libraries\CoDrone\utility\EEPROMs.cpp.o
Compiling core...
Using precompiled core
Linking everything together... [more hidden path details]

Using library CoDrone at version 1.4.4 in folder: C:\Users\Anjelica Thang\Documents\Arduino\libraries\CoDrone 
Sketch uses 9066 bytes (28%) of program storage space. Maximum is 32336 bytes.
Global variables use 1262 bytes of dynamic memory.
[hidden path details]

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\Users\Anjelica Thang\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.0.1-arduino5/etc/avrdude.conf"

         Using Port                    : COM10
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
         AVR Part                      : ATmega32
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom         4    10    64    0 no       1024    4      0  9000  9000 0xff 0xff
           flash         33     6    64    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           calibration    0     0     0    0 no          4    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino
         Hardware Version: 2
         Firmware Version: 1.16
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e9502
avrdude: reading input file "C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229/Test_Flight.ino.hex"
avrdude: writing flash (9066 bytes):

Writing | ################################################## | 100% 0.95s

avrdude: 9066 bytes of flash written
avrdude: verifying flash memory against C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229/Test_Flight.ino.hex:
avrdude: load data flash data from input file C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229/Test_Flight.ino.hex:
avrdude: input file C:\Users\ANJELI~1\AppData\Local\Temp\arduino_build_93229/Test_Flight.ino.hex contains 9066 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.95s

avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x002e
         0x78 != 0xaf
avrdude: verification error; content mismatch

avrdude done.  Thank you.

the selected serial port 
 does not exist or your board is not connected

Please let me know if there a fix for this. Thank you!

[robolink_leila]

@athang ,
It looks like your SmartInventor board is having a problem and you will need to send it back for a repair. I will have someone email you so that it can be arranged
When you get your new board, make sure you also update your CoDrone library. It seems like you have an old version. In Arduino, go to Sketch>Include Library>Manage Libraries...

Search for CoDrone and make sure to click "Update" to the most recent version.